行業資訊
壓路機運行時的碾壓原則
來源：http://m.fggwj.com/ 日期：2022-09-15
壓路機運行時的碾壓原則您知道是什么嗎？為了后面使用該機器更好的進行施工，相關運行的原則就要知道，下面濟南壓路機出租人員就來講講這個問題。
Do you know what the rolling principle is when the roller is running? In order to use the machine for better construction, we need to know the relevant operation principles. Now, the taxi staff of Jinan Road Roller will talk about this problem.
1、壓路機壓路時要從公路的邊沿壓起，壓實路面逐漸向公路中間移動。前側的軋輥應具有一定的重疊寬度，雙輥式壓路機與單輪式壓路機的交迭寬度為250~300mm，而三輪式壓路機的交疊寬度應為主壓輪的二分之一左右。
1. When rolling, the road roller shall lift from the edge of the road, and the compacted road surface shall gradually move towards the middle of the road. The roll at the front side shall have a certain overlap width. The overlap width of the double roll roller and the single wheel roller shall be 250~300mm, while the overlap width of the three wheel roller shall be about half of the main roller.
2、壓路機碾壓技術：在工作過程中，壓路機應該在起動前啟動，而內燃發動機應先達到中等速度，再轉到高速。當坡面非常陡峭的時候，須先用小型壓路機進行預壓，然后用重型壓路機或壓路機進行壓實。
2. Rolling technology of road roller: in the working process, the road roller should be started before starting, and the internal combustion engine should reach the medium speed first, then turn to the high speed. When the slope is very steep, a small roller shall be used for pre compaction first, and then a heavy roller or roller shall be used for compaction.
3、在直線上進行壓實，壓實應遵循“由輕到重、由慢到快、由邊到中（曲線段按先內、后外）”的原則。使用1次靜壓+3-4次震動+1次靜壓的方法，運行速度以3-6公里/小時為宜。
3. Compaction shall be carried out on a straight line, following the principle of "from light to heavy, from slow to fast, and from edge to middle (the curve section shall be first inside and then outside)". Use the method of one static pressure+3-4 shocks+1 static pressure, and the operating speed is 3-6 km/h.
4、將壓路機盡可能的接近攤鋪機，采用先輕后重的加壓方式進行壓路，以保證混凝土在冷卻到至小溫度之前能滿足密實度的要求。在碾碎新的瀝青路面時，為了降低路面的起皺和開裂，駕駛員應先把主動輪開到新鮮的混合料場中。保證沖擊碾壓的速度是恒定的，在熱料層上不能隨意停頓、轉彎，而且起步要慢，以減少壓痕。
4. The road roller shall be close to the paver as much as possible, and the road shall be compacted in a light to heavy way to ensure that the concrete can meet the requirements of compactness before it is cooled to a low temperature. When crushing the new asphalt pavement, in order to reduce the wrinkling and cracking of the pavement, the driver should first drive the driving wheel to the fresh mixture yard. Ensure that the speed of impact rolling is constant, do not stop or turn at will on the hot material layer, and start slowly to reduce the indentation.
此外，無論是上坡還是下坡，都應該把壓路機的傳動輪放在后方。這樣可以保證上坡時，后輪能承受斜坡和機械本身的推動力，而前輪在地面上進行初步壓縮，從而抵抗來自驅動輪的強大剪切力；下坡時，由于壓路機自身重量所帶來的沖力由主動輪的剎車所抵消，而只有前車輪碾壓后的混合料具有支撐后驅動輪的剪力。
In addition, the driving wheel of the roller should be placed behind both uphill and downhill. This can ensure that the rear wheel can withstand the driving force of the slope and the machine itself when going uphill, while the front wheel is preliminarily compressed on the ground to resist the strong shear force from the driving wheel; When going downhill, the impact brought by the roller's own weight is offset by the brake of the driving wheel, while only the mixture rolled by the front wheel has the shear force supporting the rear driving wheel.
壓路機運行時的碾壓原則就是如此內容了，希望給您好的幫助，當然平常要注意對機器設備的保養維護哦。更多相關事項就來我們網站http://m.fggwj.com咨詢吧！
This is the principle of rolling when the road roller is running. I hope to help you. Of course, you should pay attention to the maintenance of machinery and equipment. Come to our website for more information http://m.fggwj.com Consult!
公司地址：濟南市商河縣賈莊鎮民營經濟創業園
公司名稱:永誠廣建公路材料（山東）有限公司 
備案號：